Subject overview

Fluid Statics

Pressure, hydraulic force transmission, hydrostatic pressure and density.

01

Pressure and Force

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Uniform normal load over the specified area. Pressure is force per area; tangential force is excluded. One bar equals exactly 100000 Pa.

02

Static Pressure Contributions

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Both contributions use the same pressure reference. The hydrostatic contribution is positive for increasing depth.

03

Gauge and Absolute Pressure

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Signed gauge pressure is absolute pressure minus ambient pressure. Negative gauge pressure indicates underpressure, not negative absolute pressure.

04

Underpressure Magnitude

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Applicable when absolute pressure is at most ambient pressure. The underpressure is a nonnegative magnitude.

05

Hydraulic Press

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Steady ideal conditions; no pressure losses. Use consistent gauge pressures; this is not a hydraulic-system design or safety calculation. Pistons are at the same height; p = F₁/A₁ = F₂/A₂. Force amplification does not create energy.

06

Hydrostatic Pressure

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Enter known quantities; each independent relation is evaluated as soon as it is determined.

Static incompressible fluid of constant density and uniform gravity. The result is pressure relative to the free surface, not absolute pressure. Add the surface pressure separately.

Uniform incompressible fluid and uniform gravity. This inverse form also permits solving for gravitational acceleration without a default value.

Uniform column of fluid of mass m above cross-section A; p = mg/A = ρgh. Surface pressure is excluded.

07

Mass, Density and Volume

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Homogeneous material with constant bulk density. Density depends on material and temperature; provide an appropriate value.

08

Buoyant Force

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Archimedes’ principle in a uniform fluid. Use displaced volume, not height: the source’s force formula omits the volume factor and is dimensionally incorrect.

09

Net Buoyancy of a Fully Immersed Body

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Leave one model quantity empty; enter the others to calculate it.

Fully immersed body, uniform densities; upward force is positive. F = F_A − F_G = (ρ_fluid − ρ_body) g V. The source’s height factor is corrected to volume.

10

Surface Tension

Calculate

Numbers or expressions: (), +, -, *, /, ^. Prefixes: 1.5k, 250m, 20u. Results: 3 significant figures. Input help

Enter known quantities; each independent relation is evaluated as soon as it is determined.

Constant surface energy density. A is the total new interface area; include both faces for a film when applicable. N/m and J/m² are equivalent units.

Force component tangential to the interface. Effective line length includes all interfaces; contact-angle projections must already be included.